Waterbed Heaters
*We Will Beat Any Price On Same or similar product
But Please remember, quality remains long after price is forgotten
Click here to view full Warranty
Please note that the Warranty is on the heater only not service work if item is faulty.
Waterbed service persons normally charge for service.
Our charges are usually
lower than most.
TROUBLE SHOOTING
Make sure the pad is placed in the bed according to instructions.
If you see the indicator light on the dial will be a dull consistant light, no matter where the dial is pointing
A, Check the connection from the pad under the control and make sure the plug is firmly in the control.
B, If A is OK, then the other alternative is the pad is faulty. This is rare.
Checking the dial
A, Start at the right position [ie 3pm, cords hanging down] The light should be totally off
B, Slowly [like the second hand on a clock] turn anti-clockwise to the warm position
C, The light should come on at about the mid [or Noon ] position. The light may also come on before or after the mid position depending on pad temperature D, At the warm position [ie 9am] the light should be steady and bright If bed is cold after checking pad and control. Do a restart see HEATER INSTRUCTIONS
If the light does not work.
1, If pad is not hot then check power (Use other GPO's)
2, Check power board [ In some cases one ou
tlet in board could be faulty
3, Double check 1 & 2
4, Then replace control in nearly all cases If the light is always on then the pad is very cold or control is faulty If light comes on [ie 10am position] close to 9am position then pad is very warm or control is suspect When heater is at temperature the indicator light will flash on and off. This is normal |
PROUD TO BE AUSTRALIAN
Australia's one and only heater
Instructions in several languages.
An export product.
Sensor - Built in Cap - Safety Cut Out
No Tube Sensors
Pad Cord Length: 2850mm approx.
Control Dimensions:
70 x 105 x 45mm depth
Pad Dimensions 340mm x 955mm
$139
HEATER 350 watt [complete unit] to suit most types of waterbeds in Australia [see 100w below] Less including tube beds and some Gel Beds
HEATER 100 watt [complete unit] to suit waterbed types 100mm depth or less including tube beds. [For finer details in setting up see warranty card below ]
HEATER INSTRUCTIONS
[ Holding control with cords hanging down]
1. COLD START Turn dial to warm position and leave till mattress is warm [ie 9am]
2. Then adjust dial to centre position [ie Noon]
3. Re-adjust dial slightly for personal comfort [Suggest 24hrs between readjustments]
1. WARM START Turn dial to center position
[ie Noon]
2. Re-adjust dial slightly for personal comfort [Suggest 24hrs between readjustments]
Professional Installation service from $45
SAVE WATER !!!!!!!! NOW
We can pump the water in your mattress to our holding mattress that we treat after every job. We then reverse the water back into your mattres.
-
Saves water.
-
The exact amount of water is back in
your bed.
-
Any warmth is also kept.
980mm x 350mm
22mm & 70mm
Weight inc Box 1.890kg
|
Plug to control
1660mm approx
Pad only price $75
Control only price $75
Delivery
Free Local
Express postage extra
Enquiries,
Service Bookings,
Purchase Heater:
Phone 07 3803 4999
or 0429 0429 88
24 hrs/7 days
Heater plug conection to control
4 pin cresent shape compatable
with all other Aqua Plus heaters
with same pin configuration,
even from decades ago
Holding mattress
|
|
AQUAPLUS HEATERS ARE VERY RELIABLE HEATERS AND HAVE PROVEN THEMSELVES TIME AND TIME AGAIN
A waterbed success story !
Spotters fee
Dreamlover customers always receive our products at everyday low prices. When you order on the web and find a competitors price has fallen below our every day low price we will match the heater price plus give you a further 10% discount as well. This is not in conjunction with any other offers.
All Customers
Please note that all heater orders require 24 hours to process unless marked urgent and will usually be shipped the following business day. Orders placed on Friday will be shipped the following Monday. Depending on the chosen shipping method, holidays may delay packages by an additional day.
We stand by the products we sell
There are many out there that are still working successfully 18 years on, but for peace of mind :
How to Deal with Heater warranties wherever you are in Australia
a. Notify us by phone 0418 196808, email jawrge@hotmail.com, SMS 0418 196808 for best contact times
b. We need you near the heater when calling to confirm your trouble shooting testing accuracy [ see our guide above]
c. Over the phone we will guide you to do a series of tests as in the trouble shooting guide for us to determine the problem.
d. We will then send a replacement part to you by post or other arrangement between us. When you have changed over the faulty part, we then ask you to send back the faulty part so we in turn can claim this with the manufacturer
e. You can come to our shop for a replacement
or
as per warranty card see [ warranty card ] - Defective parts should be returned PREPAID to
AQUA ADVANCE INDUSTRIES PTY LTD . P.O. Box 6467 Wetherill Park 2164
or to us
Big George Waterbeds
P.O. Box 100
Waterford
Queensland
Australia 4133
|
![Dreamaster 350w yellow lettering, 200w green lettering [shown] and 100w blue lettering](images/A2-Dreamaster-200w-th.jpg)
